Search Harmonised Standards in ASEAN: HS

Conducting and dissipative rubbers, vulcanized or thermoplastic -- Measurement of resistivity / ISO 1853:2011

ISO 1853:2011 specifies the requirements for the laboratory testing of the volume resistivity of specially prepared test pieces of vulcanized or thermoplastic rubber compounds rendered…  [More Details+]

Rubber -- Determination of ash / ISO 247:2006

ISO 247:2006 specifies two methods for the determination of ash from raw rubbers, compounded rubbers and vulcanizates. The methods are applicable to raw, compounded or…  [More Details+]

Rubber -- Determination of metal content by atomic absorption spectrometry -- Part 4: Determination of manganese content / ISO 6101-4:2014

ISO 6101-4:2014 specifies an atomic absorption spectrometric method for the determination of the manganese content of rubbers. The method is applicable to raw rubber and…  [More Details+]

Rubber -- Guide to the calibration of test equipment / ISO 18899: 2013

ISO 18899:2013 outlines the principles of calibration of rubber test equipment and gives guidance on the general requirements for ensuring measurement traceability, establishing the basis…  [More Details+]

Rubber -- Guide to the use of curemeters / ISO 6502:1999

This International Standard provides guidance on the determination of vulcanization characteristics of rubber compounds by means of curemeters.  [More Details+]

Rubber test mixes -- Preparation, mixing and vulcanization -- Equipment and procedures / ISO 2393:2014

ISO 2393:2014 specifies the equipment and procedures for the preparation, mixing, and vulcanization of rubber test mixes specified in the various International Standards for the…  [More Details+]

Rubber — Determination of metal content by atomic absorption spectrometry — Part 3: Determination of copper content / ISO 6101-3:2014

ISO 6101-3:2014 specifies an atomic absorption spectrometric method for the determination of the copper content of rubbers. The method is applicable to raw rubber and…  [More Details+]

Rubber, vulcanized or thermoplastic -- Accelerated ageing and heat resistance tests / ISO 188:2011

ISO 188:2011 specifies accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers. Two methods are given: Method A: air-oven method using a cell-type…  [More Details+]

Rubber, vulcanized or thermoplastic -- Antistatic and conductive products -- Determination of electrical resistance / ISO 2878: 2011

ISO 2878:2011 specifies a method of test to determine the electrical resistance of antistatic and conductive products manufactured wholly or in part from rubber whose…  [More Details+]

Rubber, vulcanized or thermoplastic -- Determination of hardness (hardness between 10 IRHD and 100 IRHD) / ISO 48:2010

ISO 48:2010 specifies four methods for the determination of the hardness of vulcanized or thermoplastic rubbers on flat surfaces (standard-hardness methods) and four methods for…  [More Details+]

Rubber, vulcanized or thermoplastic -- Determination of shear modulus and adhesion to rigid plates -- Quadruple-shear methods / ISO 1827:2011

ISO 1827:2011 specifies methods for the determination of the modulus in shear and the strength of bonds of rubber to metal or other rigid plates,…  [More Details+]

Rubber, vulcanized or thermoplastic -- Determination of tensile stress-strain properties / ISO 37:2011

ISO 37:2011 describes a method for the determination of the tensile stress-strain properties of vulcanized and thermoplastic rubbers. The properties which can be determined are…  [More Details+]

Rubber, vulcanized or thermoplastic -- Determination of tension set under constant elongation, and of tension set, elongation and creep under constant tensile load / ISO 2285: 2013

ISO 2285:2013 specifies a number of methods of determining the dimensional changes in test pieces of vulcanized or thermoplastic rubber during and after tensile loading…  [More Details+]

Rubber, vulcanized or thermoplastic -- Determination of the effect of liquids / ISO 1817:2015

ISO 1817:2015 describes methods of evaluating the resistance of vulcanized and thermoplastic rubbers to the action of liquids by measurement of properties of the rubbers…  [More Details+]

Rubber, vulcanized or thermoplastic -- Resistance to ozone cracking -- Part 1: Static and dynamic strain testing / ISO 1431-1:2012

ISO 1431-1:2012 specifies procedures intended for use in estimating the resistance of vulcanized or thermoplastic rubbers to cracking when exposed, under static or dynamic tensile…  [More Details+]