Search Harmonised Standards in ASEAN: ASEAN BODY

Conducting and dissipative rubbers, vulcanized or thermoplastic -- Measurement of resistivity / ISO 1853:2011

ISO 1853:2011 specifies the requirements for the laboratory testing of the volume resistivity of specially prepared test pieces of vulcanized or thermoplastic rubber compounds rendered…  [More Details+]

General purpose rubber thread — Specification / ISO 20058:2017

ISO 20058:2017 specifies physical and mechanical requirements for rubber threads. It does not apply to rubber threads for food contact, furniture, high heat resistance and…  [More Details+]

ISO 1436 Rubber hoses and hose assemblies -- Wire-braid-reinforced hydraulic types for oil-based or water-based fluids -- Specification / ISO 1436:2009

ISO 1436:2009 specifies requirements for six types of wire-braid-reinforced hose and hose assembly of nominal size from 5 to 51 plus, for one of the…  [More Details+]

Latex, rubber -- Determination of total solids content / ISO 124:2014

ISO 124:2014 specifies methods for the determination of the total solids content of natural rubber field and concentrated latices and synthetic rubber latex. These methods…  [More Details+]

Natural rubber latex cleanroom gloves — Specification / ISO 20437:2017

ISO 20437:2017 gives the specification for ISO 4, ISO 5 and ISO 6 cleanroom gloves. It is applicable to cleanroom gloves made of natural rubber…  [More Details+]

Natural rubber latex concentrate -- Determination of alkalinity / ISO 125:2011

ISO 125:2011 specifies a method for the determination of the alkalinity of natural rubber latex concentrate. The method is not necessarily suitable for latices from…  [More Details+]

Natural rubber latex concentrate -- Determination of boric acid content / ISO 1802:1992

This International Standard specifies a procedure for the determination of boric acid in natural rubber latex concentrate. The procedure is not necessarily suitable for latices…  [More Details+]

Road vehicles — Brake hose assemblies for hydraulic braking systems used with non-petroleum-base brake fluid / ISO 3996:1995

Specifies the test procedures for, and performance requirements and marking of hydraulic brake hose assemblies to be used in hydraulic brake systems of road vehicles…  [More Details+]

Road vehicles — Elastomeric boots for cylinders for drum type hydraulic brake wheel cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 120 degrees C max.) / ISO 4927:2005

ISO 4927:2005 specifies performance tests for moulded rubber boots used at end closures on drum type wheel brake cylinders. These boots prevent the entrance of…  [More Details+]

Road vehicles — Elastomeric boots for drum-type, hydraulic brake wheel cylinders using a non-petroleum base hydraulic brake fluid (service temperature 100 degrees C max.) / ISO 6117:2005

ISO 6117:2005 specifies performance tests for moulded rubber boots used at end closures on drum type wheel brake cylinders; these boots prevent the entrance of…  [More Details+]

Road vehicles — Elastomeric cups and seals for cylinders for hydraulic braking systems using a non-petroleum base hydraulic brake fluid (Service temperature 120 degrees C max.) / ISO 4928:2006

ISO 4928:2006 specifies performance tests of brake cups and seals for hydraulic braking systems for road vehicles; it does not include requirements relating to chemical…  [More Details+]

Road vehicles — Elastomeric cups and seals for cylinders for hydraulic braking systems using a non-petroleum base hydraulic brake fluid (service temperature 70 degrees C max.) / ISO 6118:2006

ISO 6118:2006 specifies performance tests of brake cups and seals for hydraulic braking systems for road vehicles. It does not include requirements relating to chemical…  [More Details+]

Road vehicles — Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 120 degrees C max.) / ISO 6119:2006

ISO 6119:2006 specifies the performance test methods and requirements for elastomeric seals used in road vehicle disc brake cylinders. It is applicable to solid section…  [More Details+]

Road vehicles — Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 150 degrees C max.) / ISO 4930:2006

ISO 4930:2006 specifies the performance test methods and requirements for elastomeric seals used in road vehicle disc brake cylinders. It is applicable to solid section…  [More Details+]

Road vehicles — Elastomeric seals for hydraulic disc brake cylinders using a petroleum base hydraulic brake fluid (service temperature 120 degrees C max.) / ISO 7632:1985

Specifies the performance test methods and requirements for seals used in disc brake cylinders. Applies to solid section type seals (square, rectangular,'O'-ring) mounted stationary in…  [More Details+]

Rubber -- Determination of ash / ISO 247:2006

ISO 247:2006 specifies two methods for the determination of ash from raw rubbers, compounded rubbers and vulcanizates. The methods are applicable to raw, compounded or…  [More Details+]

Rubber -- Determination of magnesium content of field and concentrated natural rubber latex by titration / ISO 11852:2011

This International Standard specifies titration methods for the determination of the magnesium content of field and concentrated natural rubber latex, respectively.  [More Details+]

Rubber -- Determination of metal content by atomic absorption spectrometry -- Part 4: Determination of manganese content / ISO 6101-4:2014

ISO 6101-4:2014 specifies an atomic absorption spectrometric method for the determination of the manganese content of rubbers. The method is applicable to raw rubber and…  [More Details+]

Rubber -- Guide to the calibration of test equipment / ISO 18899: 2013

ISO 18899:2013 outlines the principles of calibration of rubber test equipment and gives guidance on the general requirements for ensuring measurement traceability, establishing the basis…  [More Details+]

Rubber -- Guide to the use of curemeters / ISO 6502:1999

This International Standard provides guidance on the determination of vulcanization characteristics of rubber compounds by means of curemeters.  [More Details+]

Rubber and plastics hoses -- Method of test for flammability / ISO 8030:2014

ISO 8030:2014 specifies a method for assessing the flammability of hoses, except for hoses intended for use with petroleum fuels for combustion engines. The method…  [More Details+]

Rubber and plastics hoses and hose assemblies -- Guidelines for selection, storage, use and maintenance / ISO 8331:2014

ISO 8331:2014 sets out recommendations designed to maintain rubber and plastics hoses and hose assemblies, prior to use, in a condition as close as possible…  [More Details+]

Rubber and plastics hoses and tubing -- Determination of transmission of liquids through hose and tubing walls / ISO 8308: 2006

ISO 8308:2006 specifies two methods for the determination of transmission of liquids through hose and tubing walls. Both methods are applicable to rubber and plastics…  [More Details+]

Rubber and plastics hoses, non-collapsible, for fire-fighting service -- Part 1: Semi-rigid hoses for fixed systems / ISO 4642-1:2009

ISO 4642-1:2009 specifies the requirements and test methods for semi-rigid reel hoses for fire-fighting purposes for use with fixed systems. The hoses are intended for…  [More Details+]

Rubber and plastics hoses, non-collapsible, for fire-fighting service -- Part 2: Semi-rigid hoses (and hose assemblies) for pumps and vehicles / ISO 4642-2:2009

ISO 4642-2:2009 specifies the requirements and test methods for semi-rigid reel hoses for use on fire fighting vehicles and trailer pumps. The hoses are intended…  [More Details+]

 1 2 3 >