Search Harmonised Standards in ASEAN: ICS

General purpose rubber thread — Specification / ISO 20058:2017

ISO 20058:2017 specifies physical and mechanical requirements for rubber threads. It does not apply to rubber threads for food contact, furniture, high heat resistance and…  [More Details+]

ISO 1436 Rubber hoses and hose assemblies -- Wire-braid-reinforced hydraulic types for oil-based or water-based fluids -- Specification / ISO 1436:2009

ISO 1436:2009 specifies requirements for six types of wire-braid-reinforced hose and hose assembly of nominal size from 5 to 51 plus, for one of the…  [More Details+]

Natural rubber latex cleanroom gloves — Specification / ISO 20437:2017

ISO 20437:2017 gives the specification for ISO 4, ISO 5 and ISO 6 cleanroom gloves. It is applicable to cleanroom gloves made of natural rubber…  [More Details+]

Road vehicles — Brake hose assemblies for hydraulic braking systems used with non-petroleum-base brake fluid / ISO 3996:1995

Specifies the test procedures for, and performance requirements and marking of hydraulic brake hose assemblies to be used in hydraulic brake systems of road vehicles…  [More Details+]

Road vehicles — Elastomeric boots for cylinders for drum type hydraulic brake wheel cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 120 degrees C max.) / ISO 4927:2005

ISO 4927:2005 specifies performance tests for moulded rubber boots used at end closures on drum type wheel brake cylinders. These boots prevent the entrance of…  [More Details+]

Road vehicles — Elastomeric boots for drum-type, hydraulic brake wheel cylinders using a non-petroleum base hydraulic brake fluid (service temperature 100 degrees C max.) / ISO 6117:2005

ISO 6117:2005 specifies performance tests for moulded rubber boots used at end closures on drum type wheel brake cylinders; these boots prevent the entrance of…  [More Details+]

Road vehicles — Elastomeric cups and seals for cylinders for hydraulic braking systems using a non-petroleum base hydraulic brake fluid (Service temperature 120 degrees C max.) / ISO 4928:2006

ISO 4928:2006 specifies performance tests of brake cups and seals for hydraulic braking systems for road vehicles; it does not include requirements relating to chemical…  [More Details+]

Road vehicles — Elastomeric cups and seals for cylinders for hydraulic braking systems using a non-petroleum base hydraulic brake fluid (service temperature 70 degrees C max.) / ISO 6118:2006

ISO 6118:2006 specifies performance tests of brake cups and seals for hydraulic braking systems for road vehicles. It does not include requirements relating to chemical…  [More Details+]

Road vehicles — Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 120 degrees C max.) / ISO 6119:2006

ISO 6119:2006 specifies the performance test methods and requirements for elastomeric seals used in road vehicle disc brake cylinders. It is applicable to solid section…  [More Details+]

Road vehicles — Elastomeric seals for hydraulic disc brake cylinders using a non-petroleum base hydraulic brake fluid (Service temperature 150 degrees C max.) / ISO 4930:2006

ISO 4930:2006 specifies the performance test methods and requirements for elastomeric seals used in road vehicle disc brake cylinders. It is applicable to solid section…  [More Details+]

Road vehicles — Elastomeric seals for hydraulic disc brake cylinders using a petroleum base hydraulic brake fluid (service temperature 120 degrees C max.) / ISO 7632:1985

Specifies the performance test methods and requirements for seals used in disc brake cylinders. Applies to solid section type seals (square, rectangular,'O'-ring) mounted stationary in…  [More Details+]

Rubber and plastics hoses, non-collapsible, for fire-fighting service -- Part 1: Semi-rigid hoses for fixed systems / ISO 4642-1:2009

ISO 4642-1:2009 specifies the requirements and test methods for semi-rigid reel hoses for fire-fighting purposes for use with fixed systems. The hoses are intended for…  [More Details+]

Rubber and plastics hoses, non-collapsible, for fire-fighting service -- Part 2: Semi-rigid hoses (and hose assemblies) for pumps and vehicles / ISO 4642-2:2009

ISO 4642-2:2009 specifies the requirements and test methods for semi-rigid reel hoses for use on fire fighting vehicles and trailer pumps. The hoses are intended…  [More Details+]

Rubber hoses and hose assemblies -- Textile-reinforced hydraulic types for oil-based or water-based fluids -- Specification / ISO 4079:2009

ISO 4079:2009 specifies requirements for five types of textile-reinforced hydraulic hose and hose assembly of nominal size from 5 to 100. They are suitable for…  [More Details+]

Rubber hoses and hose assemblies for automobile power-steering systems -- Specification / ISO 11425:1996

Specifies requirements for five types of hose and hose assembly used in automobile power-steering systems, the five types differing in their pressure ratings and volumetric…  [More Details+]

Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles -- Specification / ISO 8789:2009

ISO 8789:2009 specifies the requirements for rubber hoses and hose assemblies, up to a maximum hose size of 19, for use in motor vehicles with…  [More Details+]

Rubber hoses and hose assemblies for measured fuel dispensing -- Specification / ISO 5772:1998

This International Standard specifies the requirements for three types of rubber hose and hose assembly used for measured fuel dispensing, including oxygenated fuels (up to…  [More Details+]

Rubber hoses and tubing for air and vacuum systems for internal-combustion engines -- Specification / ISO 11424:1996

Specifies requirements for vulcanized-rubber hoses and tubing for use in the various air and vacuum systems found on internal-combustion engines. Does not cover hoses used…  [More Details+]

Rubber hoses and tubing for cooling systems for internal-combustion engines -- Specification / ISO 4081:2010

ISO 4081:2010 specifies the requirements for straight or pre-formed rubber hoses and tubing for use in pressurized or unpressurized cooling circuits containing 1,2-ethanediol-based coolants in…  [More Details+]

Rubber threads — Methods of test / ISO 2321:2017

ISO 2321:2017 specifies methods of test for determining general physical and mechanical properties of rubber threads, as well as specific mechanical properties of such threads…  [More Details+]

Rubber, vulcanized — Preformed joint seals for use between concrete paving sections of highways — Specification / ISO 4635:2011

ISO 4635:2011 specifies requirements for material for preformed vulcanized rubber joint seals used between concrete paving sections of highways. It is applicable to seals for…  [More Details+]

Ships and marine technology — Floating pneumatic rubber fenders Part 1: High pressure / ISO 17357-1:2014

ISO 17357-1:2014 specifies the material, performance, and dimensions of high-pressure floating pneumatic rubber fenders, which are intended to be used for the berthing and mooring…  [More Details+]

Ships and marine technology — Floating pneumatic rubber fenders Part 2: Low pressure / ISO 17357-2:2014

ISO 17357-2:2014 specifies the material, performance, and dimensions of low-pressure floating pneumatic rubber fenders, which are intended to be used for the berthing, and mooring…  [More Details+]

Single-use medical examination gloves -- Part 1: Specification for gloves made from rubber latex or rubber solution / ISO 11193-1 : 2008 Ed 2

ISO 11193-1:2008 specifies requirements for packaged sterile, or bulked non-sterile, rubber gloves intended for use in medical examinations and diagnostic or therapeutic procedures to protect…  [More Details+]

Single-use medical examination gloves -- Part 2: Specification for gloves made from poly(vinyl chloride) / ISO 11193-2 : 2006 Ed 1

ISO 11193-2:2006 specifies requirements for packaged sterile, or bulked non-sterile, poly(vinyl chloride) gloves intended for use in medical examinations, and diagnostic or therapeutic procedures, to…  [More Details+]