Search Harmonised Standards in ASEAN: HS

Conducting and dissipative rubbers, vulcanized or thermoplastic -- Measurement of resistivity / ISO 1853:2011

ISO 1853:2011 specifies the requirements for the laboratory testing of the volume resistivity of specially prepared test pieces of vulcanized or thermoplastic rubber compounds rendered…  [More Details+]

ISO 1436 Rubber hoses and hose assemblies -- Wire-braid-reinforced hydraulic types for oil-based or water-based fluids -- Specification / ISO 1436

ISO 1436:2009 specifies requirements for six types of wire-braid-reinforced hose and hose assembly of nominal size from 5 to 51 plus, for one of the…  [More Details+]

Rubber -- Determination of ash / ISO 247:2006

ISO 247:2006 specifies two methods for the determination of ash from raw rubbers, compounded rubbers and vulcanizates. The methods are applicable to raw, compounded or…  [More Details+]

Rubber -- Determination of metal content by atomic absorption spectrometry -- Part 4: Determination of manganese content / ISO 6101-4:2014

ISO 6101-4:2014 specifies an atomic absorption spectrometric method for the determination of the manganese content of rubbers. The method is applicable to raw rubber and…  [More Details+]

Rubber -- Guide to the calibration of test equipment / ISO 18899: 2013

ISO 18899:2013 outlines the principles of calibration of rubber test equipment and gives guidance on the general requirements for ensuring measurement traceability, establishing the basis…  [More Details+]

Rubber -- Guide to the use of curemeters / ISO 6502:1999

This International Standard provides guidance on the determination of vulcanization characteristics of rubber compounds by means of curemeters.  [More Details+]

Rubber and plastics hoses -- Method of test for flammability / ISO 8030:2014

ISO 8030:2014 specifies a method for assessing the flammability of hoses, except for hoses intended for use with petroleum fuels for combustion engines. The method…  [More Details+]

Rubber and plastics hoses and hose assemblies -- Guidelines for selection, storage, use and maintenance / ISO 8331:2014

ISO 8331:2014 sets out recommendations designed to maintain rubber and plastics hoses and hose assemblies, prior to use, in a condition as close as possible…  [More Details+]

Rubber and plastics hoses and tubing -- Determination of transmission of liquids through hose and tubing walls / ISO 8308: 2006

ISO 8308:2006 specifies two methods for the determination of transmission of liquids through hose and tubing walls. Both methods are applicable to rubber and plastics…  [More Details+]

Rubber and plastics hoses, non-collapsible, for fire-fighting service -- Part 1: Semi-rigid hoses for fixed systems / ISO 4642-1:2009

ISO 4642-1:2009 specifies the requirements and test methods for semi-rigid reel hoses for fire-fighting purposes for use with fixed systems. The hoses are intended for…  [More Details+]

Rubber and plastics hoses, non-collapsible, for fire-fighting service -- Part 2: Semi-rigid hoses (and hose assemblies) for pumps and vehicles / ISO 4642-2:2009

ISO 4642-2:2009 specifies the requirements and test methods for semi-rigid reel hoses for use on fire fighting vehicles and trailer pumps. The hoses are intended…  [More Details+]

Rubber hoses and hose assemblies -- Textile-reinforced hydraulic types for oil-based or water-based fluids -- Specification / ISO 4079:2009

ISO 4079:2009 specifies requirements for five types of textile-reinforced hydraulic hose and hose assembly of nominal size from 5 to 100. They are suitable for…  [More Details+]

Rubber hoses and hose assemblies for automobile power-steering systems -- Specification / ISO 11425:1996

Specifies requirements for five types of hose and hose assembly used in automobile power-steering systems, the five types differing in their pressure ratings and volumetric…  [More Details+]

Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles -- Specification / ISO 8789:2009

ISO 8789:2009 specifies the requirements for rubber hoses and hose assemblies, up to a maximum hose size of 19, for use in motor vehicles with…  [More Details+]

Rubber hoses and hose assemblies for measured fuel dispensing -- Specification / ISO 5772:1998

This International Standard specifies the requirements for three types of rubber hose and hose assembly used for measured fuel dispensing, including oxygenated fuels (up to…  [More Details+]

Rubber hoses and hose assemblies for water suction and discharge -- Specification / ISO 4641:2010

ISO 4641:2010 specifies the minimum requirements for textile-reinforced, smooth-bore rubber water-suction and discharge hoses and hose assemblies. Three types of hoses and hose assemblies are…  [More Details+]

Rubber hoses and tubing for air and vacuum systems for internal-combustion engines -- Specification / ISO 11424:1996

Specifies requirements for vulcanized-rubber hoses and tubing for use in the various air and vacuum systems found on internal-combustion engines. Does not cover hoses used…  [More Details+]

Rubber hoses and tubing for cooling systems for internal-combustion engines -- Specification / ISO 4081:2010

ISO 4081:2010 specifies the requirements for straight or pre-formed rubber hoses and tubing for use in pressurized or unpressurized cooling circuits containing 1,2-ethanediol-based coolants in…  [More Details+]

Rubber hoses, textile-reinforced, for compressed air -- Specification / ISO 2398:2006

ISO 2398:2006 specifies the requirements for three types, three classes and two categories of textile-reinforced rubber hose for compressed air, up to a maximum working…  [More Details+]

Rubber hoses, textile-reinforced, for general-purpose water applications -- Specification / ISO 1403:2005

ISO 1403:2005 specifies the requirements for three types of general-purpose textile-reinforced rubber water hose with an operating temperature range of -25 °C to +70 °C…  [More Details+]

Rubber or plastics hoses and hose assemblies -- Hydraulic-pressure impulse test without flexing / ISO 6803:2008

ISO 6803:2008 describes hose impulse testing, without flexing, of rubber or plastics hydraulic hose assemblies at both high and low impulse pressures. The high-pressure testing…  [More Details+]

Rubber test mixes -- Preparation, mixing and vulcanization -- Equipment and procedures / ISO 2393:2014

ISO 2393:2014 specifies the equipment and procedures for the preparation, mixing, and vulcanization of rubber test mixes specified in the various International Standards for the…  [More Details+]

Rubber — Determination of metal content by atomic absorption spectrometry — Part 3: Determination of copper content / ISO 6101-3:2014

ISO 6101-3:2014 specifies an atomic absorption spectrometric method for the determination of the copper content of rubbers. The method is applicable to raw rubber and…  [More Details+]

Rubber, vulcanized or thermoplastic -- Accelerated ageing and heat resistance tests / ISO 188:2011

ISO 188:2011 specifies accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers. Two methods are given: Method A: air-oven method using a cell-type…  [More Details+]

Rubber, vulcanized or thermoplastic -- Antistatic and conductive products -- Determination of electrical resistance / ISO 2878: 2011

ISO 2878:2011 specifies a method of test to determine the electrical resistance of antistatic and conductive products manufactured wholly or in part from rubber whose…  [More Details+]

 < 1 2